I know a lot of people in Europe bought the iPhone and want to downgrade to 1.1.1 to unlock it. Here is how its done:
NOTE: This guide does not guarantee it will work 100%. Also errors 1015 is expected at the end of the process. Continue reading to understand.
1. Download the 1.1.1 ipsw firmware file from Apple. If the downloaded file has the extension “.zip”, please remove it and modify it to end up with a filename ending in _Restore.ipsw
2. Reboot your iPhone holding the top (power) and home buttons BUT release the top button 10 seconds into it (right after the screen goes dark) and continue to hold the home button until iTunes detects the phone in recovery mode. The iPhone screen will appear to be off, but start iTunes if not started yet .
3. Restore your iPhone by pressing and holding the ‘Shift’ key on windows or ‘option’ key on Mac, then click ‘restore’ to select the 1.1.1 firmware file you downloaded earlier. The restore should go through and errors at the end with error 1015. However you will notice that the iphone is in DFU mode with the connect to itunes screen from 1.1.1.
In order to kick the phone out of that mode I just had to launch iNdependence version 1.2.5 and wait a minute or so.
Now you are ready to follow the easy steps at the following LINK in order to reactivate the phone:
http://iphoneunlocked.mostofmymac.com/Unlocking_Instructions.html
PS: And for those who wonder about IPSF, I tried to run it on my downgraded iPhone and it could not unlock the phone. It errors with “Unable to download firmware”. We should expect and update from IPSF shortly!
Info taken from Hackint0sh, thank them if you like it.
November 10th, 2007 at 12:55 am
reinstalling 1.1.2 worked fine…but still can’t get back to 1.1.1
November 10th, 2007 at 1:34 am
i got it work but i had to use iPhuc on windows because iNdependence wouldn’t work
November 10th, 2007 at 9:07 am
but the iNdependence isn’t just for the MAC ?? i have a windows XP help me
November 10th, 2007 at 1:32 pm
David, how did you use iphuc to get it to work? i can get the iphone to have 1.1.1 software. with the error 1015. what did you then to in iphuc?
November 11th, 2007 at 6:17 am
Same please let us know what your inputting to iPhuc, iNdependence on’t recognise the iPhone…
November 12th, 2007 at 7:38 pm
sometimes independence doesn’t work to restart from recovery mode.
i use ibrickr to restart from this condition (if it’s not 1.0.2) or i use apptapp installer (for 1.0.2)
November 13th, 2007 at 8:03 am
Any easy downgrade solution for Windows yet?
November 14th, 2007 at 7:38 pm
i need help if i dont activate it and it says activate iphone can still folow the steps to downgrade.
sombody please help me!
November 14th, 2007 at 8:32 pm
I must be a idiot someone please help me downgrade to 1.1.1 again I’m to scared to screw my phone up.. i will pay
November 14th, 2007 at 9:26 pm
The message server could not be found keeps coming up everytime i try and launch safari whne i followed the instructions for th iphone from being jailbroken.
November 16th, 2007 at 9:44 am
dude i cant seeam to duo this and my phone is locked.i was not trying to upgade but i hit the wrong button and i think i am fucked plz help some one i have been up for two day straight trying to fig. this shit out
November 17th, 2007 at 1:38 am
i have installed the 1.1.1 firmware with 1015 error now how can i use iNdependence version 1.2.5 in windows.
November 17th, 2007 at 1:39 am
Plzzzzzzz help me out
November 18th, 2007 at 5:41 pm
everytime i download the frikin 1.1.1 file, it converts it to a folder. wot file do i choose from within it????
November 19th, 2007 at 12:15 pm
were i could download 1.1.1 ipsw??? please show me the link/url… thanks
November 20th, 2007 at 2:58 pm
How to exit the DFU mode after you got to error 1015 if you are using Windows? iNdependence is application for MAC user only.
November 20th, 2007 at 8:10 pm
i was also trying to downgrade to 1.1.1 so that i could unlock it but had the same error 1015. what do i do from here? please help!
November 20th, 2007 at 11:06 pm
So i wanna downgrade to 1.1.1 but i cant do it…i d/l the firmware but all it did was delete all my information restarted the iphone, restored it to the latest upgraded version 1.1.2….So any smart ass out there plz help me i really want the 1.1.1 on my iphone…Please be helpful….thnx have a happy thanks givin
November 22nd, 2007 at 6:03 am
Hey
ANyone out there who managed to downgrade a recently bought V1.1.2 iphone (not updated from any other versions) to v1.1.1? Pls post it up here!
thank you
I see many ppl having prob bcoz they are using windows. WHy not borrow sum1’s mac to work on it? or go to a computer shop with mac and pay them to use their mac for 1 hour?
November 22nd, 2007 at 6:04 am
Help pls
November 22nd, 2007 at 7:56 am
sugandha>> You have to press shift(on windows) or alt(on mac) and click restore on itunes when ur iphone is in restore mode.
November 22nd, 2007 at 7:57 am
madhav>> error 1015 is okay. actually it means ur baseband is a later version, however, proceed with the guide you are using.
November 22nd, 2007 at 7:58 am
toZnoMeiZtErq>> dun use ipsf. it needs money and the staff are very ignorant. use anysim. after revirginizing.
November 22nd, 2007 at 7:59 am
rudy>> please explain ur situation.
November 22nd, 2007 at 9:28 pm
Shawn>>>after the 1015 error what do you mean launch independence? Where can I get it and will it work for windows, can you please go over the steps in more detail? Also, will I bbe able to use apptapp3 for 3rd pty apps I’d will I need to something else? Thanks for you help!
November 23rd, 2007 at 8:36 am
After downgrading (1015) and quitting iTunes, iNdependence crashes immediatelly. From XP, iBrickr would not work because of ‘Problem registering main callback: -402653180′. I am stuck in recovery mode…
November 25th, 2007 at 5:12 am
i have done everything i am stuck trying to install oktoprep but it say installing and immediatley goes to my home screen it never really install it someone help.. pleaseeeee
November 27th, 2007 at 4:38 pm
After i get the 1015 error i close itunes and lauch independence but nothing happens all the buttons are greyed out and it just says connected to iphone in recovery mode?????? please help ive been trying for weeekksss to downgrade to 1.1.1 PLEASSSSSS HELPPPPP thanks
November 29th, 2007 at 5:47 am
Hi all, it seems like using iNdependence to kick iPhone out of this mode works best with iTunes 7.4.1 -
Note: DON’T USE 7.4.2 as my phone kept restarting itself in some crazy loop when I tried. PS if anyone knows where people can download 7.4.1 mac and windows please post it. thanks.
November 29th, 2007 at 8:34 am
Hi guys,
I have successfully updated 2 iphones from 1.1.1 to 1.1.2 and jail breaked and unlocked..( pse note both these phones are with old boot loaders) I also got the same errors trying to install appsnap on 1.1.1 and running anysim 1.2 on 1.1.1.
For sake of all pse try to follow these steps
1. Ensure boot loader is 3.9 and NOT 4.6
2. update/ restore 1.1.2 ( whatever be your current firmware)
3. Put ur iphone into DFU mode ( either ibrickr or Sleep&Home keys trick)
4. Downgrade to 1.0.2
5. Use Winstaller to activate, jailbreak and Update installer,
6. install installer and update
7 install BSD subsystem
8 Install anysim 1.2 and run
9 Make sure u can make and recieve phone calls on 1.0.2
10 install oktoprep
11 UPDATE to 1.1.2 with itunes
12 Jail break 1.1.2
13. Install iworld if you are using iphone in a country in which it is not released.
Deliberately I have avoided all links…. pse google for all dowload files… all the best…..
December 1st, 2007 at 5:40 am
hey manoj can u pls mail the procedure for downgrading to 1.1.1.. i tried a lot but i couldn;t get it ..
December 1st, 2007 at 3:47 pm
HELP!! I recently bought an iphone with 1.1.2 pre installed on it and I managed to downdgrade to 1.1.1 finally. It actually worked, I had 1.1.1 working on my phone until, I tried to upgrade to 1.1.2 through itunes and the using jailbreak. Thats where everything went wrong. My phone is now stuck in recovery mode. Restore didn’t work for 1.1.1 or 1.1.2. Any sugesstions on what I should do next would be greatly appreciated and please dont say buy another phone. Thanks
December 3rd, 2007 at 1:20 pm
hi guys, i just ordered a new iphone online, im not a genious when it comes to all this jargon u guys use i really need to know can a new iphone with 1.1.2 be downgraded and then unlocked? can i keep 1.1.2 and unlock it? i really need to know if it can be done o/w i should cancel my order. im in pakistan and it requires a huge effort to order the iphone, i hope it works and is worth it.
December 3rd, 2007 at 3:41 pm
waleed:
Cancel your order! All brand new iPhones come with bootloader 4.6 and can not be unlocked (at the moment) hackers are trying to get around this but currently no solution.
December 3rd, 2007 at 3:57 pm
FOR EVERYONE TRYING TO DOWNGRADE TO 1.1.1 USING WINDOWS:
1. Put your iPhone into DFU mode
2. In iTunes hold the shit key and click on ‘Restore’
3. Select the 1.1.1 firmware file and hit ‘OK’
4. After about 4 minutes you will get an error (That’s OK)
5. Close iTunes
6. Download and Install iPhuc.exe
7. Type each of these commands on their own line and hit enter for each:
cmd setenv auto-boot true
cmd saveenv
cmd fsboot
exit
8. Wait a few seconds and your iPhone should be out of DFU mode and at the activation screen.
Put iPhone in DFU mode: With iTunes still open and the iPhone still connected, press and hold the Sleep/Wake button and the Home button until the screen turns black. Once it does, let go of the Sleep/Wake button. Continue to hold the Home button until iTunes displays a pop up about the iPhone being in recovery mode. Click OK.
Firmware Files: http://www.hacktheiphone.com/112/iphone_firmware_update.html
iPhuc Install: http://code.google.com/p/iphuc/
Hope this information helps!
December 4th, 2007 at 3:27 am
i followed chadpriddle’s instruction and after step 8 my phone got back to the activation screen successfully. Now after i turned the phone off and back on again it returned to DFU mode again. I had to start over, and when I tried install appsnapp and the phone reboot it also got back to DFU mode.
any help here?
December 4th, 2007 at 4:58 pm
***REVISED*** FOR EVERYONE TRYING TO DOWNGRADE TO 1.1.1 FROM 1.1.2 USING WINDOWS:
1. Put your iPhone into DFU mode (With iTunes still open and the iPhone still connected, press and hold the Sleep/Wake button and
the Home button until the screen turns black. Once it does, let go of the Sleep/Wake button. Continue to hold the Home button
until iTunes displays a popup about the iPhone being in recovery mode. Click OK.)
2. In iTunes hold the shit key and click on ‘Restore’
3. Select the 1.1.1 firmware file and hit ‘OK’ (Download it here: http://www.hacktheiphone.com/112/iphone_firmware_update.html)
4. After about 4 minutes you will get an error (That’s OK)
5. Close iTunes
6. Download iPhuc (Download it here: http://code.google.com/p/iphuc/)
7. Launch the iphuc.exe and type each of these commands on their own line and hit enter for each:
cmd setenv auto-boot true
cmd saveenv
cmd fsboot
exit
8. Wait a few seconds and your iPhone should be out of DFU mode and at the activation screen.
***If you have an AT&T activated sim card then goto to step 9a. If not then goto step 9b***
9a. Connect to iTunes and let your iPhone activate. If your AT&T service does not work that is ok
10a. Now add your WiFi network
11a. Launch Safari and type jailbreakme.com
12a. Now go straight to step 22
***Continue if you do not have an AT&T activated sim card***
9b. Slide to reach the emergency dial screen
10b. Enter *#307# and then press call
11b. Your phone will ring itself, press answer
12b. Press hold now and your phone will start ringing again
13b. Press Dismiss and your phone will go into the contacts/dial screen
14b. Press contacts from the bottom bar and add a contact
15b. Add a contact with a random name and homepage of: prefs://1f
16b. Save it and click on the link. This will take you straight into the settings menu of the iPhone
17b. Select ‘General’ and then select ‘Auto-lock’and hit ‘Never’
18b. Now go back and add your WiFi network
19b. Hit the home button and you will now be taken back to the emergency dial screen
20b. Repeat steps 10b-14b and now add another contact with a random name and a homepage of: jailbreakme.com
21b. Save it and click on the link. This will launch safari and take you to the appsnapp install page. Continue to step 22
22. Scroll to the bottom of the page and click on ‘Install appsnapp’
23. After it installs you should have a jailbroken and activated phone with the installer.app
24. Launch installer and install ‘BSD Subsystem’ and then select the sources button at the bottom of the screen
25. Click on ‘Edit’ and then click on ‘Add’
26. Type ‘http://i.unlock.no’ the sources will refresh
27. Select the install button at the bottom of the screen and scroll down where it says ‘Unlocking Tools’
28. Now install ‘BB Downgrade’ to downgrade your 1.1.2 to 1.1.1 baseband
29. After it installs you have to re-flash the firmware for the changes to take affect. Repeat steps 1-5 above and then after
that proceed to step 30
30. So now you should have an iPhone that you downgraded to 1.1.1 from 1.1.2 and then installed appsnapp, installer, BSD
Subsystem, BB Downgrade and then re-flashed the firmware again to 1.1.1 and are now back to the activation screen
***If you have an AT&T activated sim card then goto to step 30a. If not then goto step 30b***
30a. iTunes should now activate your iPhone and your AT&T should now work
31a. Launch Safari and type jailbreakme.com and install appsnapp again. That’s it!
***Continue if you do not have an AT&T activated sim card***
30b. Repeat steps 9b-27 and then proceed to 31b
31b. Select and install anySIM and follow the instructions
32b. Restart your iPhone and that’s it!
NOTES: This is for those that want to downgrade there iPhone and baseband back to 1.1.1
This will not work with brand new out of the box iPhones that already come with firmware version 1.1.2
Sorry if the guide is a little confusing and jumps around a bit, just follow the steps!
If you restart for iPhone with 1.1.1 and have not yet downgraded your baseband then you iPhone will restart back into DFU mode
Please post comments if you have any questions
December 4th, 2007 at 11:33 pm
So there is no solution for those loosers who bought iphone with 1.1.2? how can I find out what version of bootloader i have?
thanks
December 7th, 2007 at 12:52 am
i was downloading from i tunes and i get msg to update ur phone in itunes
i have update software file was 160mb and 1.1.2 and i got error at the end
and i get into restore but i get error and my phone is not working it shows please connect to iphone on the display nothing else
plz help me
what to do
December 7th, 2007 at 5:41 pm
i downloaded the iphuc from the site posted by chadpriddle. the iphuc that is downloadable is not an exe file. please help. i get it all the way to that point and then i have no idea what to do. i am using windows. any help from this point on is greatly apreciated. thanks
December 7th, 2007 at 7:56 pm
chadpriddle >>>> on step 6-7 I downloaded iphuc-universal 7.4.2. I try to open it and it does anything. When I open i chose to open with itunes? is it the way?
How can I launch iphuc?
Thanks
December 8th, 2007 at 1:51 am
I bought an iPhone which came with v1.1.2. I know that there is no solution available to unlock the sim right now. How about iPod function? I downgraded to v1.1.1 and hope that iPod would work. But iPod also doesn’t work. Any help is appreciated.
Thanks.
December 8th, 2007 at 3:06 am
Is there any way to unlock the iPhones that come with .1.1.2 or does anyone know when apple is making or bringing out the 1.1.3. Fw
December 9th, 2007 at 3:27 pm
Chadpriddle - I have a question about your note…. So if I have a pre loaded out of the box iphone with FW 1.1.2, I cannot downgrade to 1.1.1 and jailbreak? Thats the only part im confused about. Since the note is at the end of the post and doesnt say if you are talking about unlocking or jailbreaking or both. It seems as I am stuck and cannot jailbreak because I have a preloaded 1.1.2. Please clarify.
December 9th, 2007 at 6:06 pm
I can restore on my mac to 1.1.1, but then it gets stuck and the emergency slide will not appear. I tried this from iNdependence:
then you’ll need to find the version of the MobileDevice framework that was installed with iTunes 7.4.2 and put it somewhere on your computer. Something useful might be at:
http://rapidshare.com/files/68410680/MobileDevice_7_4_2.framework.zip.html
4) Once you have that, choose the location of the MobileDevice.framework folder using the first file chooser.
5) If that works, then choose the location where you installed iNdependence on your computer using the second file chooser.
6) At this point you should see a success message.
I did that (with the mobiledevice framework) but it would not let me choose the location of the framework? and hence my phone is still in recover mode? any suggestions??
December 10th, 2007 at 6:10 pm
After Error 1015 just run iBrickr, close iTunes and chose boot phone from iBrickr menu. - Works like a charm.
Cheers
December 11th, 2007 at 7:44 am
to open Iphuc you have to go to>Start> ALL programs>IPHUC and open IPHUC for windows. If not just search for it on ur pc.
i had that trouble too, but i found it, Sucks that you cant unlock 1.1.2 yet, There is a way but u have to pay for it,
December 11th, 2007 at 2:11 pm
Hi Guys,
Is there any way to unlock the iPhones that come with .1.1.2 pre installed.
Help would be much appreciated. May be downgrading it or some other solution
December 11th, 2007 at 4:44 pm
Hey,
I bought an iphone with firmware 1.1.2 (out of the box) and I have tried everything to unlock it!
Can anyone tell me what I need to do to unlock sim lock on the iphone?
December 11th, 2007 at 10:45 pm
I NEED HELPPPPP !!
I did everything & now im down to this one step… please someone help!
on my computer it wont open up iPhuc .. what file do i have to open up with ???
December 12th, 2007 at 6:32 am
chadpriddle: whwn you say close itunes, did you ment onlly press i down ore close down all “itunes helper, itnes m.m.
December 12th, 2007 at 8:16 am
“This will not work with brand new out of the box iPhones that already come with firmware version 1.1.2″”
Yes i dose: http://youtube.com/watch?v=AdrayUqw0Uw
December 13th, 2007 at 12:58 am
you need to download 1.1.2 downgrader from conceited software
http://conceitedsoftware.com/iphone/site/112jb.html
open jailbreak.jar(windows)
and transfer the files over
(itunesmobiledevice…
qtml….
readline5…)
then iphuc.exe
and enter the codes that was given to you by chadpriddle
December 14th, 2007 at 3:46 pm
The links you keep giving for iPhuc are not for Windows. That is for Mac, and there is no iphuc.exe. How is it done for Windows?
December 16th, 2007 at 9:06 am
where can i download that 1.1.1patch?
December 16th, 2007 at 10:24 am
HELP PLZ!~~~~~~~~
what shall i do after iPhone could not be restored. An unknown error occured (1015)
how to launch iNdependence version 1.2.5
December 19th, 2007 at 7:38 am
Hi i can unlocked iphone with 1.1.2 softwere, so if some one want to please contact me. thanks
December 21st, 2007 at 1:23 am
u have to launch iDemocracy and then it will fix and your iphone will go to the activate with itunes screen.
December 23rd, 2007 at 7:51 am
[…] An example on downgrading firmware: Use of the option key is.. well.. key. Also good to know is that seeing “error 1015″ is a sign of success. […]
December 27th, 2007 at 9:11 am
Hi,I had tried several, but the green screen come on every time istead of red screen. and the error is: (6) instead of (1015). Could you please tell me why? THX
December 28th, 2007 at 4:45 pm
when i go into recover mode and itunes opens and i selet the 1.1.1 firmware. it starts to do its downgrade but then i get a “itunes cannot upgrade ” the a number “5″ is next to it it that the error code and if so what does it mean. i am currently on 1.1.2 but i want to go to 1.1.1
December 30th, 2007 at 12:52 pm
i was able to downgrade to 1.1.1 but BB downgrade specifically says it wont work on preinstalled 1.1.2 phones(out of the box) soo i cant get any serivice on 1.1.1 help chadpriddle or anyone who knows sometin
December 30th, 2007 at 4:48 pm
Hi!
I have the same problem as ateeq nagori no39. Can someone help me?
December 30th, 2007 at 7:52 pm
Kuba. Are you saying that you can unlock phones pre-installed with version 1.1.2??
December 30th, 2007 at 7:54 pm
Is there any solution out there for idiots like me who have bought the phones with 1.1.2?? Can you use any of the features for the time being?? Like the ipod?? It seems like a nice gadget….looking at it is fun.
December 31st, 2007 at 1:41 pm
I don’t know where to find 1.1.1– I looked at the apple website– so once I do that what comes next– thanks
January 1st, 2008 at 9:42 pm
I just got an iphone recently so it came with 1.1.2 firmware (OOB), i was able to bypass the activation and have acess to some features, i downgraded firmware and then used iphuc for windows, but everytime i turn off my phone it goes back to DFU mode don’t know why?, not a very big computer person, can anybody tell me how i can fix this please. And if there is a way to downgrade baseband 04.02.13_g (Out of the box), im sure you are tired of looking at this same question over and over again, but i’m just doble checking, thanks in advance…
January 2nd, 2008 at 6:32 pm
Hi Jordana,
you can find 1.1.1 right here:
http://appldnld.apple.com.edgesuite.net/content.info.apple.com/iPhone/061-3883.20070927.In76t/iPhone1,1_1.1.1_3A109a_Restore.ipsw
The link at the top of this page has really good instructions on what to do next!
Cheers, Hans
January 2nd, 2008 at 10:18 pm
hey i have an ipod touch and i wanted to jailbreak it, but im stuck on 1.1.2. I need to download it, but no one every really tells me where to download 1.1.1 at. Some people say apple, and i dont know where to find it there, and then one said mostofmymac.com, but thats buying the unlocked iphone. Can anyone help me out? email me @ monkeyboy659@hotmail.com thanks guys
January 3rd, 2008 at 4:29 pm
nothing works. 1.1.2 - games over
January 4th, 2008 at 10:50 am
If i bought a new iphone with 1.1.2 and I’m assuming it has the new bootloader, is there any way I can downgrade to 1.1.1 or 1.0.2 and unlock it? Or is the newer bootloader what is stopping me from doing so?
January 6th, 2008 at 4:23 am
this one is kinda confusing
and it hurts your brain after sevral hours of frusturation
here is a website that has pics and makes it easy to follow along on unlocking the iphone
here is the 1.1.2 tutorial(and yes it does work, my iphone is unlocked on 1.1.2)
http://www.hackthatphone.com/index_112.html
here is the 1.1.1:
http://www.hackthatphone.com/index_111.html
the 1.0.2:
http://www.hackthatphone.com/index_74.html
and apple firmware can be downloaded here:
http://wiki.howardforums.com/index.php/IPhone_Firmware_Downloads
good luck!
January 6th, 2008 at 11:59 am
hello,
I have bought a iphone 1.1.2 and I would like downgrade to 1.1.1, but I can’t. I have always an error (1403) and I can’t see the error (1015). WHY? Here’s someone to help me????
January 6th, 2008 at 6:20 pm
just keep goin
the error number difference shouldn’t really matter
January 6th, 2008 at 8:48 pm
chadpriddle, I got to step 22 , but after that the phone restarts and it goes back to the screen on 1.1.2 - asking to connect to iTunes , in recovery mode. Any ideas?
January 8th, 2008 at 3:04 am
hi, i have the iphone 1.1.2… can anyone tell me how to unlock it? do have to downgrade it to 1.1.1 to unlock it? and can i keep the V 1.1.2 and get it unlocked?? need a reply asap… im stuck with the locked phone for 3 weeks now!!!
January 8th, 2008 at 8:12 am
k so i just got an iphone preinstalled with 1.1.2 and i was wondering if i get a stealthcard to make it work can i downgrade to 1.1.1 so i can get 3rd party apps?
January 8th, 2008 at 3:17 pm
hey..urm i went on the apple website (www.apple.com) but can’t seem 2 find 1.1.1 download.+?
January 16th, 2008 at 2:00 pm
hi, im a 13 year old from israel and my father bought the iphone from the U.S. and it was already in 1.1.2 and he said that this whole process above can lock the whole entire iphone and he doesn’t want to take chances…so i need 100% proof that this process works…
January 18th, 2008 at 4:28 pm
do i have to install and run ibrickr before i shut down my iphone and restore it with the 1.1.1 firmware that i downloaded? or does that even matter at all?
January 29th, 2008 at 7:25 pm
Kevin, when u say u unlocked ur 1.1.2 phone do u mean u can get service on it also. because i could install 3rd party apps but couldnt get service. Help needed, thanks
February 2nd, 2008 at 7:53 am
Thanks for sharing
February 10th, 2008 at 5:42 am
Hi
I tried all this (mac) nothing helped. Whenever I downgrade I get the error 1015 because it does not downgrade the modem firmware. I can upgrade to 1.1.2 but then I cannot installer apptapp which means I cannot install iWorld which means I cannot use my iPhone properly.
Any idea on how I can:
either
install apptapp on a 1.1.2 phone
or
get iWorld on the 1.1.2 without using apptapp
or
downgrade my modem firmware to 1.1.1. (which means 4.2.13_G I guess)
King Kong
February 11th, 2008 at 9:02 pm
hi guys, i am another one with error 1403,
always the same error and erases the file after the error,
any idea what can be this thing?
June 24th, 2008 at 4:01 am
[…] i try and launch safari whne i followed the instructions for th iphone from being jailbroken.http://ipopho.com/iphone-112-downgrade-to-111/Found footage: Using an iPhone to control reconnaissance aircraft - tuaw.comWhile the iphone is […]